Friday, September 26, 2014

Nokia 1200 mother board short solution

Now I will show how to is repair nokia 1200 mother board short problem.When short motherboard then mobile phone is standby short time.It is very Disturbance so it repairing is very important.View the below picture and work step by step.

How to do this work : If any repairer face this problem then first clean full pcb goodly with petrol or thiner.next check red mark parts,If you see short one of them then replace that parts.

Samsung Metro E2202 Hard Reset Instructions

If you are owner of Samsung Metro E2202 phone and you have problem with your phone for example hang up or the operating system cant run, maybe this instructions can help you. This is troubleshooting for your phone especially how to hard reset for Samsung Metro E2202.

The Samsung Metro E2202 is dual sim phone that work on under GSM network with frequency of 900 / 1800 . This phone has been released last month (2013, february). It has 1.8 inches display screen and measuring 110.7 x 46 x 14.3 mm . The Samsung Metro E2202 also powered by Li-Ion 1000 mAh battery capacity and support for MP3/AAC/WAV player and MP4/H.263 player.

Before you hard reset, you must backup all important data because the data will be lost like mesagges, contacts, etc. Ok, the following tutorial for the Samsung Metro E2202 resetting as follows:
- Enter *2767*3855#
- To SIM or make backup to your PC before full reset! Take out SIM
card before full reset.
- Your default security phone lock code preset 00000000 / eight zeros

Thursday, September 25, 2014

Nokia n85 keypad 0 problem solved by jumper

Nokia n85 keypad 0 problem solved by jumper

Procedure follow Lcdshot

JellyBean 4 1 0 For Galaxy Y

Want to get Android 4.1 Jelly Bean taste on your Galaxy Y? Yes, of course you can. Find out details after the jump!Thanks to S5360 custom ROM for Android 4.1 Jelly bean, now you can update your Galaxy Y to Android 4.1. In this post you will learn how to update your Samsung Galaxy Y to Android 4.1 Jelly Bean using S5360 custom ROM. Before you proceed, you will need to have fulfilled following requirements:

You have to install your Galaxy Y USB Drivers on your PC.
You need to enable USB debugging mode which is deactivated by default.
You smartphone should have minimum 80% charge remaining.
Your Galaxy Y should be Rooted.
This guide is only meant for Galaxy Y GT-S5360, dont try it on other variants of Galaxy Y. You can check your Galaxy Y version in Settings –> About phone.
Last but not least, backup your important data like Call logs, SMS and other data in stored in phone memory so in case if anything goes wrong, your data is not hurt.

How to Install Android 4.1 Jelly Bean Custom ROM on Galaxy Y

Step 1) DOWNLOAD Android 4.1 Jelly Bean Custom ROM for Galaxy Y.

Step 2) Connect your Galaxy Y USB to your computer using the USB cable.

Step 3) Copy the downloaded file to your SD card.

Step 4) Turn off your phone and then turn it in again in the recovery mode by pressing and holding the Volume UP + Home Button + Power Key buttons.

Step 5) Now you will see exclamation mark on your phone Lcd. Again hold your volume up and power buttons. Now your Galaxy Y is in recovery mode.

Step 6) Once your smartphone is in ClockworkMod recovery, you are ready to perform a Nandroid backup of your existing ROM. For that you will need to select Backup and Restore option followed by selecting Backup again in next windows. Once the backup is completed, you are ready to go back to main recovery menu.

Step 7) Now you will need to wipe the previous ROM first. For that select Wipe data/factory reset option and select Yes to confirm the action.

Step 7) Now select Install zip from sdcard and then select choose zip from sdcard.

Step 8) Navigate to Custom ROM file we have just uploaded to SD card in step 3 and select it using power button. Confirm the installation on the next Lcd and the installation procedure should start now.

Step 9) Once installation is completed, go back to main recovery menu and select Reboot System Now.

Recommended: Before rebooting your phone from CWM Recovery, go to CWM Recovery main menu and select Wipe Data Cache under Advance option to perform the Data cache wiping.

Nokia c2 01 ear speaker ways

This is Nokia c2-1 ear speaker ways solution.If your phone has this problem then repair ypur phone using this solution just follow this picture.

HTC Desire 600 dual sim Factory data reset

How to perform soft reset and hard reset ( master reset ) HTC Desire 600 dual sim via Settings menu and External hardware keys:

Hard reset via Settings menu

Slide the Notifications panel open, and then tap Settings
Tap Backup & reset.
Tap Reset phone.
If you also want to delete media and other data on HTC Desire 600, select Erase
all data.
Tap OK.

To avoid permanent damage to your device, do not restart your device while a reset procedure is underway.

Warning! All data will be erased from device memory, including system and application data, settings and downloaded applications. Back up your important data. The device will restore to factory settings.

Hard reset via external hardware keys

Remove the battery, wait for a few seconds, then reinsert the battery.
Press and hold the VOLUME DOWN button, and then press and hold the POWER button.
Wait for the Lcd with the three Android images to appear, and then release the POWER and VOLUME DOWN buttons.
Press VOLUME DOWN to select FACTORY RESET, and then press the POWER button.

Only do this if you can not do it via Setting menu.

Performing Soft Reset

If the display is off, press the POWER button to turn it back on.
Unlock the display.
Press and hold the POWER button, and then tap Restart.
When asked to confirm, tap Restart.

Wednesday, September 24, 2014

nokia c6 01 some new solution here

Mmc solution

All Samsung Unlocker v1 30

Supported Modeles:
unlock Samsung
SGH
500,60,8x0,2100,2200,2400,N100,N300,N400,N500,N600,N620,N625
A100,A110,A2x0,A300,A400,M100,R200,R210,R220,T100,T108,Q100,
Q200,S105
Download here

HTC Desire Bootloader and Recovery

HTC Desire Bootloader and Recovery

Phoenix Service Software 2012 4 3 47798

Phoenix Service Software 2012 4 3 47798

Download Here

Hard Reset Garmin Nuvi 600 series to Factory default settings

Hard

Hard Reset Garmin Nuvi 600 series to Factory default settings

Performing a master reset Garmin Nuvi 600 to Factory default settings. It will erase all data and also all entered truck profiles:

Turn power Off and unplugged from power
Touch and hold the lower right corner of the Lcd with an index finger or the eraser end of a pencil
Continue touching and holding the lower right hand corner of the Lcd then power the device ON
Release the power button when the device powers ON
You will see a new message: “Do you really want to erase all user data?”
Remove your finger from the touch Lcd when this message displays
Touch Yes

If text language is not in English, this is the button on the right
The device will now reset. Follow the on-Lcd prompts and then place your device in an area with a clear view of the sky until it acquires satellites.

Tuesday, September 23, 2014

Update Galaxy Note 8 0 N5100 with XXBMF1 Jelly Bean 4 1 2 Firmware

Galaxy Note 8.0 N5100 can now be updated with the Official Android 4.1.2 XXBMF1 Jelly Bean Firmware which comes with the added stability and bug fixes. Just in case if you still haven’t got the update of this firmware, you can now manually update the same. The best part of this update is that this is the Official firmware and not the beta or custom ROM firmware. Before we proceed to check on what are the instructions to apply with this firmware, you will need to follow the list of pre requisites which we have mentioned below.

Note: Applying with this firmware won’t root / void the warranty in any manner.

Quick Pre Requisites:

Create a backup of all your data with the help of below mentioned steps. Though, you can back up the data with KIES as well, we recommend you to backup manually with the help of below mentioned steps as sometimes KIES refuses to detect the device.

SMS – Use “SMS Backup & Restore app”,
Contacts – Sync with the Gmail application,
Call Log - Call Log and Restore
Images, Songs, Videos, Files – Copy to internal / External SD Card,
APN and MMS Settings – Note down from the path “Applications > Settings > Wireless and Network > Mobile Networks > Access Point Names”

From the path “Settings > Development Options > USB debugging” enable the USB Debugging Mode. Minimum charge left in your phone is 30% or else there is a risk of device getting turned off in the middle of rooting process.

Disclaimer: Follow all the instructions mentioned in this article as if there is any damage caused due to not following instructions then we shall not be held liable or responsible. Just in case if you face any issues then we will try our level best to address the same.

Assuming that you are done with all the above mentioned steps, you can now proceed to the next page where we have mentioned the detailed guide on how to apply with this firmware update.

Procedure to Update Galaxy Note 8.0 N5100 with Jellybean 4.1.2 Firmware:

Download the Jellybean 4.1.2 Firmware Package and Odin from here to your computer. Once downloaded, extract both the files in your computer and open Odin in your computer.

Open Odin in your computer. Download Mode in Galaxy Note 8.0 can be entered by first turning Off the device and then hold Volume Down Rocker Key + Menu Button and then Power ON the device. Once the device is booted and you see the Download Mode Green Robot, you can release the button combos.

Connect your device to the computer with the help of original USB cable and then you will see that the ID : COM section will turn Yellow / Green, indicating that all the drivers are installed successfully.

Click on “PDA” to select the tar file which you got from the firmware package which is the TAR File which you got after extracting the file from the first step.

Once all the file is selected, click on “Start” to start the process of firmware update. Once the firmware update process is completed which will be mentioned in the ODIN, the Galaxy S2 device will be rebooted.

For firmware update to be finished, it will take around 2-3 minutes for applying the update. Once the device is updated successfully, the device will be rebooted. As soon as you see the Language preferences or the Home Screen, you need to disconnect the device from computer and enjoy using your phone.

Note: If the device gets into the boot loop sequence or say gets stuck in the welcome Lcd, just re insert the battery and re follow the above instructions so as to again follow the above mentioned instructions.

Do let us know in the comments section just in case if you face any issues in the process of firmware update in the comments section as we will try our level best to sort out the same.

Samsung Galaxy S i9000 All Keypad Not Working Solution

Samsung Galaxy S i9000 All Keypad Not Working Solution,Samsung Galaxy S i9000 All Keypad Not Working solution ways,Samsung Galaxy S i9000 All Keypad Hang Not Working Solution,Samsung Galaxy S i9000 All Keypad short Not Working Solution,Samsung Galaxy S i9000 All Keypad ways Not Working Solution,Samsung Galaxy S i9000 All Keypad Not Working Area which parts are damage for no woking this Solution Guide Step by Step Procedure Here.

How To Easy Root Galaxy Tab 7 7 P6800 P6810 Running On Android 3 2 Honeycomb

Root Samsung Galaxy Tab 7.7 GT-P6800/GT-P6810 easy you can now easily eradicate your GT-P6800/GT-P6810 Galaxy Tab 7.7 running on the latest official firmware. without using a PC but only use a mobile device to install an application and follow the steps very simple.

Once you rooting Galaxy Tab 7.7 GT-P6800/GT-P6810 you really can take advantage of hardware as you want. Such as install root only apps, and can access and modify the file system, can even upgrade to a better version of Android such as Android 4.3 or Android 4.4 Jelly Bean KitKat with flashing custom ROM (if there is available and) if you have a custom recovery installed . You can follow the simple instructions to find and install a custom recovery (CWM recovery or TWRP recovery) on your device.

Disclaimer: This guide is for educational purpose only. Neither True-Android team nor any developers are responsible if your device bricked after following this tutorial. Remember, rooting void your device manufacturer warranty.

Pre Requisites:

1. Backup your device data.

2. Make sure your device have at least 60% battery power. You can install an app like Battery Notifier BT Free on your Android device to check it easily.

Hope you back up all your data and settings as mentioned above. So, its time to jump into next stage of this guide.

How To Root Galaxy Tab 7.7 GT-P6800/GT-P6810 Easily

Download Framaroot and install it (open a file explorer, navigate your download and tap on it; you can also directly open the apk from browser download section to install it). If you see a warning box then you require to check Unknown sources under Settings –> Security.
Open the app and then tap on install superuser or super SU of your choice.
You will see some rooting options. Tap on any of the available rooting method and soon youll see the success message.

To confirm if you successfully rooted your Android device or not install an app called “Root Checker” which is available for free from Google PLAY store.

That’s it! You just learn how to root Galaxy Tab 7.7 GT-P6800/GT-P6810. And, that’s too without using any computer. You can fill the comment form below to ask additional help from community.

Monday, September 22, 2014

Simplicity Rom Ported from Galaxy Ace to Samsung Galaxy Y GT S5360

I am here with the Simplicity Rom for Samsung Galaxy y Users[GT-S5360]

Feautures found Over:-

1. added jelly bean layout
2. 14 Toggles
3. added jelly bean usb mount/unmount
4. Voice Search
5. Touchwizz
6. added extended power menu
7. removed unnecessary mods,apps
8. ninesky browser
9. added jelly bean styled phone calling mode
10. battery charging bug removed [while switch off ]
11. battery bug removed while charging[ when switch on]
12. some ui changes + more smoothness.....
13. No kernel integrated
14. S3 themed!

Changes from Original Port:-

Build 1
Fixed bluetooth
Fixed camera
Changed boot animation
Added Viper (see FAQ)
Changed tweaks
Added some apps
Removed bloat
Updated Playstore to 3.10.14

HOW TO FLAST THE ROM:-

[So Here am I with for the one You waiting For and Scrolling too.. Now Ill give u a perfect Way to Flash this Custom Rom... You would be Thinking this one Would be as Same as the one which Normally others are but not Like it Now.!! This One is Quite Different from Others.]

[First of All you Require to Root Your Device to avoid administrational setting.. If you dont know to Root CLICK HERE!!! If you have already Rooted.. Proceed Further]

1.Copy the the Simplicity.zip files to your SD card. [Note:- Not In Any Folder]

2. Turn off your phone and boot to Recovery Mod by pressing these buttons: volume up+home+power button. In Recovery you cant use the touch Lcd ..Can Operate only the buttons.

Volume up: Navigating UP
Volume down: Navigating Down
Home: Enter
Power: Back

3. Navigate through Volume Up and Down:-

i. Factory Data Reset

ii. Clear Cache Partition

4. After data wipe move to install zip from SD Card, then choose Update from SD and navigate toSimplicity.zip andPress the Home Button5. Wait until the installation ends.6. The first boot can take a long time.

7. After Phone Gets Switched On.. complete the Formalities asked by the Phone. and Now you are with the one of the Latest and Fastest custom Rom For Samsung Galaxy Y which no one could ever Dream Of Too...

How to solve computer automatic restart

Computer is very necessary in our daily life.Computer is a most sensitive electronics product so its may be many problem.Now I showing how to repair computer restart problem or how to solve computer restart problem.May be many reason for computer restart.

Problem #1 : If your computer restart when windows Lcd running

Solution of problem #1: Maximum time has this problem windows corrupted / Windows damage / windows file missing or effect by virus this problems solution is setup windows and scan update antivirus.

Problem #2: If your computer restart after some time of turn on.

Solution of problem #2: This type problem has may be damage cooling or ram Loose so check cooling fan if necessary change cooling fan and open ram then clean ram with tissue paper or eraser after that replace ram.

How to clean ram

Problem #3: If your computer has Suddenly restart.

Solution of problem #3: If your computer has Suddenly restart this problem has may be virus or ram Loose so first open ram then clean ram with tissue paper or eraser after that replace ram.then check your computer if problem still then windows setup.

Problem #4: If your computer has Suddenly restart or when electricity voltage drop/voltage up /down then restart problem.

Solution of problem #4: Maximum time This problem has for power supply weak so replace power
supply.

Problem#5 : Some time may be this problem for processor when processor weak or damage then may be has this problem.

Solution of problem #6: Try to solve this problem replacing processor.

NOKIA1661 EAR RINGER PATH

NOKIA1661 EAR/RINGER PATH

How To Android 4 4 2 KitKat Avatar ROM For AT T Galaxy Captivate SGH I897

It’s time to update your AT&T Galaxy Captivate SGH-I897 to latest and customized Android 4.4.2 KitKat with the help of custom firmware Avatar 5.0.4. It’s really good idea to have a customized AOSP based ROM instead of having pure AOSP ROM. Avatar 5.0.4 is based on latest Android 4.4.2 KitKat and build using CM11 source. The ROM mainly known for its extensive theme engine that it adopt from MIUI ROM. Its easy to download many cool looking free themes and change your phone look instantly. You can download and install custom firmware Avatar 5.0.4 on your AT&T Galaxy Captivate SGH-I897. Since, AT&T Galaxy Captivate SGH-I897 is capable enough to run Android 4.4.2 KitKat smoothly, Avatar 5.0.4 going to be a great experience for you. To learn how to flash this ROM, continue reading this guide to know how to install Android 4.4.2 KitKat based Avatar 5.0.4 custom ROM on AT&T Galaxy Captivate SGH-I897.
Related Readings:Install TWRP Recovery 2.6.3.7 on Galaxy Note 3 SM-N900 / SM-N9005 - How To Guide
Some of the cool Android 4.4.2 KitKat features that you will enjoy is Screen Recording, Tap to Pay (Google Wallet for everyone), NFC emulation for non nfc devices, 14% less memory usage, cloud printing from Gallery, Google Home is the new Launcher, Core System Processes Trimmed, apps are efficient and responsive on all devices, the all new procstats tool details memory use, Full-Lcd Immersive mode, seamless change in resolution during media playback, Phone dialer got local business detection, redesigned Quickoffice and many more.
As said already, this is a test build and you should expect some bugs in it. All bugs and issues expected to be fixed as development progress towards a better build.
Android

Android

Warning!
This tutorial is only for AT&T Galaxy Captivate SGH-I897. Don’t try this guide on any other Android device. Also, we (True Android Team) are not responsible for any damage caused due to the instruction given in this page. Try this at your own risk. However, it is very unlikely that your device will be damaged if you follow all the instructions as it is which are mentioned in procedure.
Pre Requisites:
1. Backup your device data. You can follow our ultimate backup guide
2. Make sure your device have at least 60% battery power. You can install an app like Battery Notifier BT Free on your Android device to check it easily.
3. You already have USB Driver Installed for AT&T Galaxy Captivate SGH-I897 in your PC. [Download USB Drivers]
4. Make sure USB Debugging is enabled otherwise you won’t able to transfer file between PC and AT&T Galaxy Captivate SGH-I897. [Guide]
5. Your device have latest CWM version 6.0.4.4 and up or TWRP 2.6.3.0 and up installed.[Guide]
If you done everything that we mentioned above then you are ready to follow step-by-step guide on how to install Android 4.4.2 KitKat based Avatar 5.0.4 ROM on AT&T Galaxy Captivate SGH-I897. In below tutorial we discussed the process assuming your device a non-touch recovery; you can complete the process using touch if applicable.
File Required(Download by clicking on it)

Avatar 5.0.4 For AT&T Galaxy Captivate SGH-I897 [Filename: avatar-5.0.4-NIGHTLY-20140124-captivatemtd.zip]
Google Apps [Filename: gapps-kk-20131119.zip] or any other 4.4 KitKat GApps

How to Install Android 4.4.2 KitKat based Avatar 5.0.4 ROM on AT&T Galaxy Captivate SGH-I897

Connect your device to PC using USB cable and then copy downloaded files to the SD card of your device. Important: Don’t extract any files.
Disconnect USB and then turn off your AT&T Galaxy Captivate SGH-I897.
Now, boot into ClockworkMod recovery by pressing and holding the Volume Up, Volume Down and Power buttons together until the Samsung logo comes up, leave all three buttons. You will see ClockworkMod recovery Lcd soon. Use Volume keys to browse between options in recovery while Power key to select an option. Alternatively try this:Recovery Mode without Key Combination.
Perform a Nandroid backup of your existing ROM that you can restore later if this new ROM not work or you want to go back into your previous ROM. To perform a backup, select Backup and Restore, then on the next Lcd, select Backup again. Go back to main recovery menu after backup is complete.
Now, perform data wiping task. To do so, select wipe data/factory reset, then select Yes on next Lcd to confirm your action. Wait few minutes till the data wipe is complete. Now come back to CWM recovery main menu. Select wipe cache partition and after wiping process done, select Wipe Dalvik Cache under advance option to perform Dalvik cache wiping.
Select install zip from sdcard, then select choose zip from sdcard (or /sdcard1 for external storage). Now, locate the Avatar 5.0.4 Zip file that you copied earlier in Step 1 and select it by pressing Power button. Confirm installation by selecting Yes – Install _____.zip on the next Lcd. The ROM installation will begin.
Once the ROM installation process end, repeat the step 6 but choose the gapps-kk-20131119.zip file instead of ROM zip to install the Google apps package.
When installation is completed, go back to the main recovery menu and select reboot system now to reboot your AT&T Galaxy Captivate SGH-I897 and boot up into Android 4.4.2 KitKat ROM Avatar 5.0.4.
Returning to Previous ROM: To go back to your previous ROM, boot into recovery, select backup and restore then restore your previous ROM by selecting it from the list.

Tutorial For TWRP Recovery Users:

Connect your device to PC using USB cable and then copy downloaded files to the SD card of your device. Important: Don’t extract any files.
Disconnect USB and then turn off your AT&T Galaxy Captivate SGH-I897.
Now, boot into TWRP recovery by pressing and holding the Volume Up, Volume Down and Power buttons together until the Samsung logo comes up, leave all three buttons. You will see TWRP recovery Lcd soon. Alternatively try this:Recovery Mode without Key Combination.
Create a Backup using TWRP Backup Option.
Perform a Factory Reset (this will delete all apps and their settings and game progress). To do this, Tap on Wipe, then at the bottom of the Lcd do a Swipe on the ‘Swipe to factory reset‘ option.
Now its time to add zip file for flashing. Tap on Install, then browse to the location where you saved the files and tap on the Avatar 5.0.4 Zip file. Then tap on Add More Zips, and add gapps-kk-20131119.zip. Now at the bottom of the Lcd, do a swipe on the Swipe to confirm flash option to begin flashing.
When installation is completed, go back to the main recovery menu and tap on Reboot and then, tap on System to reboot your AT&T Galaxy Captivate SGH-I897 and boot up into Android 4.4.2 KitKat ROM Avatar 5.0.4.
Returning to Previous ROM: To go back to your previous ROM, boot into recovery, select Backup then through Restore option, restore your previous ROM by selecting it from the list.

Congrats! Android 4.4.2 KitKat firmware based custom ROM Avatar 5.0.4 is now installed and running on your AT&T Galaxy Captivate SGH-I897. If you stuck on Avatar boot logo more than 5 minutes then go back to recovery and perform Step 5 (wiping task) few more times before rebooting your device.

MOBILE N18 Charging Solution

China Mobile Phone MOBILE N18 Charging Solution,
if you check it much give few comments about this so that others can learn form your comments also.
If you have any other Questions please do not hesitate to share with me.

Sunday, September 21, 2014

gfive w5 charging solution

Tips of gfive w5 charging repair

1.When you connect your phone with charger If you see no response on your phone then check green line ways.

2. If charging show on mobile phone but charge not save or not store then you check inside red mark parts and replace damage parts.Maximum time this problem solve replacing charging ic.

Nokia 1280 network no signal DONE tested 100

History : No signal at all..

Tools:

Analog Multimeter
Soldering Iron
Tweezer
Sol lead
copper wire

Actions taken:

Common sense ive seen the PA side that there is a corroded so i realize that maybe pa B+ supply was missing so itrace using analog tester and bingo i find it..

Finish product:

How To Root Easily I317MUMUCNA1 Android 4 3 Firmware Running on Galaxy Note 2 SGH I317M Canada Guide

Samsung Galaxy Note 2 SGH-I317M (Canada) recently get updated to the I317MUMUCNA1 4.3 Jelly Bean Firmware. If you yet to update the firmware, then update the same by following the above link. Hope you updated this latest firmware on your device and now you can root the same using our simple tutorial below. The below guide will help you to root UMUCNA1 4.3 Jelly Bean Firmware running on Galaxy Note 2 SGH-I317M. Continue reading the tutorial for complete guide.

After updating official firmware, your device no longer belongs to rooted device. So, after official firmware update, many of us prefer to root our device to enjoy some additional features that unrooted android device doesnt offer. With a rooted android device, you can install apps that ask root permission, flash various custom ROMs, install MODs and tweak various features. Root removes default bloatware apps that free-up lots of memory space and extend the battery life. However, once rooted, manufacturer warranty will be void. But you can regain the warranty by following proper unroot process. To know more about benefits of rooting android device, read- Complete Note on What is Rooting and Benefits of Rooting Android Phone.

I317MUMUCNA1

So, want to root Galaxy Note 2 SGH-I317M Running I317MUMUCNA1 4.3 Jelly Bean Firmware? Continue reading this page to get all the necessary steps to successfully root your device. The root file (CF-Auto-Root) we used in this tutorial is safe and have nearly 100% success rate. Well use Odin software to flash the root file.

The tutorial is made with simple step by step guide, so that even an android newbie user can follow and successfully root his/her device. However, in this process you may loss your personal data and settings. So, we recommend you to follow all the backup instructions before proceed to rooting guide.

Warning!

This rooting tutorial is only applicable for Samsung Galaxy Note 2 SGH-I317M model (t0ltecan). So, dont try this in any other android device. Check your device model number from- Settings-About Phone.
Rooting voids your phones manufacturer warranty. However, you can get back the warranty anytime by following proper unroot process or by flashing official firmware.
This guide is for educational purpose and you should try this at your own risk. We are not responsible if your device experience a soft brick after following this tutorial.

Pre-Requisites:

Check battery percentage, charge your device to a decent level of at least 60% battery power. Your device should not turn off during installation.
Turn on USB Debugging mode, go to Settings-Developer Options-USB Debugging
Backup important data and settings to external storage- follow this guide
Install USB driver for your device on your computer- Download Samsung USB Driver

All the above pre-requisites are very important and must be followed before proceed to installation guide. Hope you get all the above points and done as mentioned. Now, you are ready to move to the final step of this tutorial where we have arranged a step by step details guide to root Galaxy Note 2 SGH-I317M running I317MUMUCNA1 4.3 Jelly Bean firmware.

Steps to Root Galaxy Note 2 SGH-I317M Running I317MUMUCNA1 4.3 Jelly Bean through Odin:

Download CF-Auto-Root for Galaxy Note 2 I317M and extract the Zip file: CF-Auto-Root-t0ltecan-t0ltevl-sghi317m.zip
Download Odin 3.09 and extract the Zip file: Odin3_V3.09.Zip
Now, Switch off your phone and boot Galaxy Note 2 I317M into Download Mode by pressing and holding the Volume Down+Home+Power buttons together (long press until the boot Lcd appear), now press Volume Up key to proceed to Download Mode.
Run the Odin3 v3.09.exe file as an administrator (Right click on the .exe file and click on Run as administrator)
Now connect your Galaxy Note 2 I317M to your computer via USB cable
In Odin3 Lcd, you should see a COM Port number like “0:[COM7]” at ID:COM section and “Added!” text at the message box. This means your device has been detected by Odin3.
Make sure that, only the “Auto Reboot” and “F. Reset Time” options are checked.
Now, click on the PDA button and select the CF-Auto-Root-t0ltecan-t0ltevl-sghi317m.tar.md5 file.
Finally, click on the Start button to begin the rooting process, wait few moments.
Once completed, you would see “PASS!” message in ID:COM port having green background
Your phone should automatically reboot after completion
You can now disconnect your phone from computer
Finish

Congrats! You have completed the tutorial to root Galaxy Note 2 I317M running I317MUMUCNA1 4.3 Jelly Bean Firmware. Hope you successfully done the rooting process. If you followed everything as mentioned in the above tutorial, then your Galaxy Note 2 I317M should now rooted and you have complete control over your device. Now, install apps that ask root permission or flash various custom ROMs. To verify your device is rooted or not, you can download and run the Root Checker App from Google Play Store. If you have any doubt or query about the tutorial, feel free to contact with us using the comment form below, and share your rooting experience with us.

Galaxy Notes N7000 Repair Imei OK

Quote:

Welcome to Octopus Box Samsung software version 1.2.8
-----------------------------------------------------------------------------------
To connect GT-N7000 phone you have to perform the following steps:
1. Disconnect USB cable from phone.
2. Go to Menu->Settings->Applications->Development.
3. Turn on "USB Debugging" option.
4. When message is appear press "Yes".
5. Go to dial window.
6. Enter "*#7284#" number.
7. Set "USB" radio button to "PDA" value.
8. Close window.
9. Go to dial window.
10. Enter "*#9090#" number.
11. Set "Diag config" to "USB" value.
12. Restart phone.
13. Press "Read Info" in Octopus Samsung software.
-----------------------------------------------------------------------------------
Platform: Samsung Anycall
Selected port: COM1
Selected model: GT-N7000
Phone was not found on the selected port!
Searching for USB diagnostic port...
Connecting to phone on COM169
-----------------------------------------------------------------------------------
Platform: Samsung Anycall
Selected port: COM169
Selected model: GT-I5500
Detected phone model:
HW Version: XXXXXXXXXXXXXX
Phone model is not supported
Mode: Normal
Phone model:
Phone model is not supported
Phone was not found on the selected port!
Searching for USB diagnostic port...
Connecting to phone on COM169
Detected phone model: GT-N7000
HW Version: XXXXXXXXXXXXXX
Phone IMEI: 004999-01-064000-0
Firmware compiled date: Tue Dec 20 20:22:15 KST 2011
Android version: 2.3.6 (GINGERBREAD)
Phone IMEI: 004999010640000
-----------------------------------------------------------------------------------
Platform: Samsung Anycall
Selected port: COM169
Selected model: GT-N7000
Detected phone model: GT-N7000
HW Version: XXXXXXXXXXXXXX
Phone IMEI: 004999-01-064000-0
Firmware compiled date: Tue Dec 20 20:22:15 KST 2011
Android version: 2.3.6 (GINGERBREAD)
Phone IMEI: 004999010640000
-----------------------------------------------------------------------------------
Platform: Samsung Anycall
Selected port: COM169
Selected model: GT-N7000
Detected phone model: GT-N7000
HW Version: XXXXXXXXXXXXXX
Firmware compiled date: Tue Dec 20 20:22:15 KST 2011
Android version: 2.3.6 (GINGERBREAD)
Phone IMEI: 004999010640000
Old IMEI: 004999-01-064000-0
New IMEI: 359616-04-863474-5
Writing new IMEI. Please wait...
New IMEI successfully writed.
Please, restart phone to apply changes
Link

Saturday, September 20, 2014

Latest EXAM 2 4 1 2 JB Official ROM Update for Galaxy Young GT S6310

Samsung Galaxy GT-S6310 Young received a new official firmware update DXAMI2 Android Jelly Bean 4.1.2 firmware. Samsung has just released an OTA update of the firmware. S6310DXAMI2 latest firmware build version. The Galaxy Young was released in February of this year with Android 4.1.2 Jelly Bean. Samsung has not released the Android 4.2.2 version of android Jelly Bean or more for the device. If you already have the tools and the latest firmware is not updated, the latest firmware update using our simple tutorial below. You can check the latest available firmware for your device via OTA (over the air) from Settings-About Phone-Software Update.

Because Young Galaxy has been running on Android 4.1.2 Jelly Bean, you can only expect a slight bug fixes and performance enhancements with this update. So, want to update to the latest S6310 Young Galaxy DXAMI2 Jelly Bean Android 4.1.2 firmware? To install the official way, either you can go for the OTA update as mentioned above or download the firmware via Samsung Kies utility. However, most of us prefer the manual way to update the official firmware. So, in this article you will enjoy the step-by-step user guide for the Android 4.1.2 update DXAMI2 latest firmware on your Galaxy Young S6310 via Odin.

Important Note:

"The firmware is released only for the Samsung Galaxy Young GT-S6310 model, so don’t try this in any other android device. Check your device model number from Settings-About Phone. Also the tutorial is based on Youngdows PC. Follow all the pre-requisites, procedures and steps carefully to avoid breaking your phone".

Android 4.1.2 Jelly Bean S6310DXAMI2 Official Firmware Download List

Samsung rolled out the firmware for the following countries. The firmware which are unbranded or not locked to any carrier, no matter of which country or region, can be flashed on any Galaxy Young GT-S6310 model.

Malaysia: S6310DXAMI2_S6310OLBAMI2_XME.zip
Vietnam: S6310DXAMI2_S6310OLBAMI2_XXV.zip

[Firmware for rest of the countries and carrier will be added here when available]

Pre-Requisites:

Check battery percentage, your device should have at least 60% battery power
Turn on USB Debugging mode, go to Settings-Developer Options-USB Debugging
Backup important data and settings to external storage- follow this guide
Install USB driver for your device on your computer- Download Samsung USB Driver

Points to be Noted:

If you are using any Custom ROM such as- CyanogenMod, Paranoid Android, AOKP, SLIM ROMs etc, then it’ll replaced by this official Stock ROM
Custom Recovery (CWM or TWRP Recovery) will be replaced by Stock Recovery
After flashing official firmware, your device will no longer belongs to rooted device. However you can root your device any time after flashing the firmware.

All the above pre-requisites are very important and must follow before proceed to installation guide. Hope you get all the above points. Now, go through the below tutorial to install Android 4.1.2 S6310DXAMI2 official firmware on Galaxy Young S6310.

How to Install Android 4.1.2 Jelly Bean Official Firmware on Galaxy Young S6310 through Odin:

Download Android 4.1.2 DXAMI2 Firmware for Galaxy Young S6310 from the above list
Download Odin 3.07
Switch off your phone and boot Galaxy Young S6310 into Download Mode by pressing and holding the Volume Down+Home+Power buttons (long press until the boot Lcd appear), now press Volume Up key to proceed to Download Mode.
Extract the downloaded Odin3.07 zip file and run the Odin3 v3.07.exe file as an administrator (Right click on the .exe file and click on Run as administrator)
Now connect your Galaxy Young S6310 to your computer via USB cable
In Odin3 Lcd, you should see a COM Port number like “0:[COM7]” at ID:COM section and “Added!” text at the message box. This means your device has been detected by Odin3.
Make sure that, only the “Auto Reboot” and “F. Reset Time” options are checked.
Now, extract the downloaded firmware zip file, you’ll find a firmware file with extension.tar.md5
In Odin Lcd, click on PDA button and select the firmware file with .tar.md5 extension(The firmware file look something like: S6310XXDLJ5_S6310ODDDLI7_INU.tar.md5)
Now, click on the Start button to begin the installation process, wait few moments.
Once completed, you would see “PASS!” message in ID:COM port having green background
Your phone should automatically reboot after completion
You can now disconnect your phone from computer
Finish

Congrats! you complete the tutorial for Android 4.1.2 official firmware update Jelly Bean on the GT-S6310 Galaxy young. Hope you managed to do the update process. If youve followed everything in the tutorial as mentioned above, then you should now young Galaxy runs on the latest Android 4.1.2 Jelly Bean build DXAMI2 version. You can confirm the details of the firmware update from Settings-About Phone. If you are stuck in a point or find any problems with the download link, then please do not hesitate to contact with us using the comment form below.

Nokia BB5 Reaper 2006 v3 0 1 7

Nokia

Downloadhttp://rapidshare.com/files/168661614/BB5_Reaper-2006_fixedgsm.blogspot.com.rar

ICS Aura V1 for Samsung Galaxy Y GT S5360

Installation Process

1.Copy the the ics aura v1 final.zip files to your SD card. [Note:- Not In Any Folder]
2. Turn off your phone and boot to Recovery Mod by pressing these buttons: volume up+home+power button. In Recovery you cant use the Lcd ,only the buttons.

Volume up: up
Volume down: down
Home: Enter
Power: Back

3. Navigate through Volume Up and Down:-

i. Factory Data Reset

ii. Clear Cache Partition

4. After data wipe move to install zip from SD Card, then choose .zip from SD and navigate toics aura v1 final.zip
5. Wait until the installation ends.
6. The first boot can take a long time.

Nokia 101 RH 131 Latest Firmware mcu ppm cnt Free DOWNLOAD

Nokia Latest update flash file firmware with free Direct download And Now Enjoy This Time

Nokia 101 RH-131 Version 4.30 latest flash files Free direct download only 3 files MCU,PPM,CNT just click on file for direct download

Latest Version 4.30
1) MCU
2) PPM
3) CNT
Version 4.10
1) MCU
2) PPM
3) CNT

NOKIA 5130 MMC Solution

NOKIA 5130 MMC Solution,

Manual Update Samsung Galaxy S4 GT I9500 with XXUBMEA Jellybean 4 2 2 firmware

Samsung Galaxy S4 GT I9500 smartphone can now be updated with the XXUBMEA Jellybean 4.2.2 firmware. Though there is no official date on by Samsung will be rolling out this update worldwide, you can apply this update manually. Though there is no exact change log of this update, you can still go ahead and apply this update which we will be guiding you on how to apply. Before we proceed on to check on how you can apply with this release, proceed with the pre requisites first to the detailed instruction guide in the next page.

Quick Pre Requisites:

All the data in your Samsung Galaxy S4 should be backed up with the help of below mentioned steps manually and not with the KIES PC Suite.

SMS – Use “SMS Backup & Restore app”,
Contacts – Sync with the Gmail application,
Call Log - Call Log and Restore
Images, Songs, Videos, Files – Copy to internal / External SD Card,
APN and MMS Settings – Note down from the path “Applications > Settings > Wireless and Network > Mobile Networks > Access Point Names”

From the path “Settings > More > Development Options > USB debugging” enable the USB Debugging Mode.

Minimum charge left in your phone is 30% or else there is a risk of device getting turned off in the middle of rooting process.

Disclaimer: Follow all the instructions mentioned in this article as if there is any damage caused due to not following instructions then we shall not be held liable or responsible. Just in case if you face any issues then we will try our level best to address the same.

Assuming that you are done with the above 3 pre requisites, you can now follow the list of instructions below for rooting your Galaxy S4.

Procedure to Update Galaxy S4 I9500 with XXUAMDL Jellybean 4.2.2 Firmware:

Download the Jellybean 4.2.2 XXUBMEA Firmware Package and Odin from here to your computer. Once downloaded, extract both the files which you have downloaded in your computer. Open Odin in your computer.

Turn Off your device so that it can be entered in the Download Mode. Download Mode in GALAXY S4 can be entered by first turning Off the device and then hold Volume Down Rocker Key + Menu Button and then Power ON the device. Once the device is booted and you see the Download Mode Green Robot, you can release the button combos.

Connect your device to the computer with the help of original USB cable and then you will see that the ID : COM section will turn Yellow / Green, indicating that all the drivers are installed successfully.

Click on “PDA” in odin to select the rooting tar file which will be there in the extracted folder to click on “Start” to start the process of rooting. Once the device is updated, the device will be rebooted automatically. It may take longer time than expected for booting the device. The whole process of firmware update might take anywhere between 10 -15 minutes depending upon various conditions.

Don’t disconnect the device from computer till you see the home Lcd in your phone or the Language selection options.

Note: If the device gets into the boot loop sequence or say gets stuck in the welcome Lcd, just re insert the battery and re follow the above instructions so as to again follow the above mentioned instructions.

Do let us know in the comments section just in case if you face any issues in the process of firmware update in the comments section as we will try our level best to sort out the same. For all those who wishes to root their Samsung Galaxy S4 GT I9500 smartphones, we will be coming out with a separate tutorial which will help you root the device.

Friday, September 19, 2014

Nokia E73 USB not charging problem solution

Nokia E73 USB charging problem jumper ways solution

nokia

Top 10 Android Apps and Most popular mobile platform

Top 10 Android Apps and Most popular mobile platform : Android powers hundreds of millions of mobile devices in more than 190 countries around the world. Its the largest installed base of any mobile platform and increasing fast—every day another million users power up their Android devices for the first time and begin looking for apps, games, and other digital content.

Android gives you a world-class platform for creating apps and games for Android users all over the place, as well as an open marketplace for distributing to them instantly.

Top 10 Andriod Apps :

1. Sky Safari Pro
2. Mobile Observatory – Astronomy
3. SkEye | Astronomy
4. Distant Suns (max)
5. Star Chart
6. Stellarium Mobile Sky Map
7. Astronomy Picture of the Day

8. Vortex Planetarium – Astronomy

9. Planetarium

10. Night Sky Tools – Astronomy

Necessity of Most popular platform :

1. Large installed base and Global partnerships
2. Powerful development framework
3. Open marketplace for distributing apps

Asha 203 Asha 202 Keypad how to fix problem

This article is about Nokia Asha 202 Keypad Problem Solution. It also applies to Nokia Asha 203 Keypad Problem Solution.

Keypad problem in Nokia Asha 202 and Asha 203 can be caused by a busted Keypad IC. In the diagram below I have marked keypad IC with Red Square. First clean the area around it and the front of the motherboard to be sure that moisture or carbon is not causing this problem. If that does not work replace the Nokia Asha 202 Keypad IC.

Please Note that we will edit these solutions or add new ones if found in this page at any time in the future. So feel free to come back any time on this page to stay up to date.

If you have further Questions please dont hesitate to leave a comment.

Note: Every repairing solution posted here is tested by at least one member of our team. Use the information available here at Your Own Risk. We are not responsible if any harm comes to your device during the repairing process.

How to Start the Smart Connect Application on Sony Xperia Z1

Wouldnt it be nice if youre phone automatically plays your song list right when you step in your car? Or what about letting you show your whole day agenda the moment you arrive at your work table between 8-9am? These are just examples on how Smart Connect app works. With this app, you can set an event to happen on your device at certain times or what will happen when you connect/disconnect accessories like headset or charger. Hereshow to use it.

1. On your devices home Lcd, tap on

.
2. Look for Smart Connect and tap on it.
3. If its your first time opening the said app, tap on OK to close the introduction Lcd.
4. Go to Events tab and tap on the plus (+) icon.
5. Type in a name for the event and tap on Create.
6. Under When, add either an accessory ( like what happens on your device when you connect your headset) or a time interval or could be both.
7. Under Do This, add what you want to happen on your device.
8. Under At the End, add what you want to happen to your device when you disconnect your accessory or when the time interval ends.
9. Press on Back Arrow

to save the event.

BLACKBERRY 8320 SOLUTION

BLACKBERRY 8320 SOLUTION

Subscribe to: Posts (Atom)

blogger statistics